Why Is the BJT's Active Region Called Saturation When Ic Remains Constant?

In summary, the output characteristics of a BJT show that in the active region, the collector current remains constant regardless of the collector-emitter voltage, which is known as saturation. However, the base current is actually controlling the amount of current that Vcc supplies, and the base-emitter voltage is what truly determines the collector current. This can be seen through the equation Ic = (Vcc - Vce)/Rc, where varying Vce does not directly affect Ic. Understanding this concept is crucial in understanding the behavior of a transistor.
  • #1
Maharshi Roy
25
1
From the output characteristics of a BJT, it is observable that in the active region, the collector current becomes constant or independent of collector emitter voltage. So, in true terms, it is saturation, then why do we call it the active region?
Also, we have the equation:-
Ic = (Vcc – Vce)/Rc
Then, accordingly, with varying Vce, Ic should vary. Please clarify.
 
Engineering news on Phys.org
  • #2
You have it backwards. In a BJT in saturation the Vce of the BJT is roughly constant (and about 0.1 or 0.2 V). You are confusing saturation in a MOSFET with saturation in a BJT.
 
  • #3
Maharshi Roy said:
From the output characteristics of a BJT, it is observable that in the active region, the collector current becomes constant or independent of collector emitter voltage. So, in true terms, it is saturation, then why do we call it the active region?
Also, we have the equation:-
Ic = (Vcc – Vce)/Rc
Then, accordingly, with varying Vce, Ic should vary. Please clarify.

One of the things that get people super confused (including myself at one point) is the presumption that the base current is being magnified to form the collector current. This notion is perpetrated so much in books that saturation of the transistor almost seems impossible. What is happening is that the base current is controlling the amount of current that Vcc supplies. If you understand this very simple fact, you've unlocked the mystery of the transistor. Here's further explanation :

Assume you have Vcc connected to Rc in series without the transistor, directly to ground. Whats the current that Vcc can supply Rc ? Its Vcc/Rc. This is the maximum current that Vcc can supply.
Now put the transistor in place. The base current now dictates the collector current. So even though the source would like to supply Vcc/Rc, the transistor prevents that from happening by dropping some of Vcc across its terminals, Vce. The larger is Vce, the smaller is the current that Vcc can supply. The larger is the base current, the smaller is Vce. This means that Vcc can now supply more current than before. So let's say that you have a base current that causes the transistor to supply Vcc/Rc. What happens if you increase the base current ? Nothing ! The transistor cannot supply Vcc cannot supply more than Vcc/Rc.

In short:
Keeping Vcc and Rc constant, a small base current will cause Vcc to supply a small collector current. This also means that Vcc drops most of its voltage across its terminals as Vce.
Increasing the base the current causes Vcc to supply more collector current. This also means that Vce is getting smaller. As long as the base current can control what Vcc can supply, the transistor is said to be operating in the linear in the linear region.
 
  • Like
Likes fellowohboy
  • #4
amenhotep, thank you so much for that explanation! I stumbled around on the web and books for an hour before coming to your post which just clarified my understanding so well :)
 
  • #5
amenhotep said:
What is happening is that the base current is controlling the amount of current that Vcc supplies. If you understand this very simple fact, you've unlocked the mystery of the transistor. Here's further explanation :
.
Just because you have mentioned the "unlocked mystery" of the transistor :
I am aware that many people believe (believe, without any proof) that the base current would "control" the collector current.
And for some applications this assumption does work. But not for all!
Therefore, I think it is helpful to mention again that the collector current of a bipolar transistor is controlled/determined by the base-emitter voltage Vbe only. The base current Ib is an (unwanted, but unavoidable) by-product.
This is not only an assertion - it is a fact which can be verified.
I do not want to start this discussion today again - because this subject was discussed already intensively also in this forum.
See here, for example:

https://www.physicsforums.com/threads/amplifiers-transistors-and-opamps.828847/

https://www.physicsforums.com/threa...istor-saturation-current.824127/#post-5175698
 
Last edited:

Related to Why Is the BJT's Active Region Called Saturation When Ic Remains Constant?

1. What is the saturation region of a BJT?

The saturation region of a BJT (Bipolar Junction Transistor) is a state in which the transistor is fully turned on and the collector current is at its maximum value. In this region, the transistor behaves like a closed switch, allowing a large amount of current to flow from the collector to the emitter.

2. How is the saturation region different from the active region of a BJT?

The active region of a BJT is a state in which the transistor is partially turned on and the collector current is directly proportional to the base current. In this region, the transistor acts as an amplifier. In contrast, the saturation region is the state in which the transistor is fully turned on and the collector current is at its maximum value, acting as a closed switch.

3. What are the conditions for a BJT to enter the saturation region?

For a BJT to enter the saturation region, the base-emitter junction must be forward biased, and the collector-emitter junction must be reverse biased. Additionally, the base current must be large enough to overcome the base-emitter junction voltage drop and drive the transistor into saturation.

4. How does the collector current behave in the saturation region?

In the saturation region, the collector current is almost constant, regardless of any changes in the base current or collector voltage. This is because the transistor is acting as a closed switch, and the collector current is limited only by the external circuit.

5. What are the effects of operating a BJT in the saturation region?

Operating a BJT in the saturation region can lead to power dissipation and potential damage to the transistor. The collector current is at its maximum, and the transistor is acting as a closed switch, so the transistor can overheat if not properly controlled. Additionally, the saturation region is not suitable for amplification, so using a BJT in this state may result in distorted or inaccurate signals.

Similar threads

Replies
10
Views
1K
Replies
5
Views
2K
  • Electrical Engineering
Replies
13
Views
4K
Replies
68
Views
4K
  • Introductory Physics Homework Help
Replies
5
Views
648
  • Electrical Engineering
Replies
7
Views
3K
Replies
10
Views
7K
  • Electrical Engineering
Replies
3
Views
2K
Replies
4
Views
21K
  • Electrical Engineering
Replies
5
Views
18K
Back
Top