- #1
Jdo300
- 554
- 5
Hello All,
I am faced with a very interesting challenge and I'd like to see if you all could give me any insights. I'm currently planning to design a linear power amplifier loosely based on the design on page 22 of this PDF file here: http://www.wadsworthmedia.com/marketing/sample_chapters/1401848567_ch05.pdf
So far, I have just been doing simulations of the circuit to get a feel for it's operation. However, I want to do a few things different with the design that are, at the moment, throwing me for a loop.
In my application, I am building an amplifier specifically for driving coils of varying inductances at frequencies from 0Hz to about 1MHz (up to 20MHz ideally, but I I'm settling for lower frequency for simplicity). I found that sticking an inductive load works fine with this amplifier design except for the fact that the amperage through the coil varies with frequency due to the coil's inductance.
What I am thinking about is modifying the schematic so that it doesn't utilize voltage regulation but current regulation to keep the coil current constant throughout the frequency range. So, in other words, I want to basically make this into a voltage to current amplifier, with, say 100mV on the input translating to 100mA through the output load.
To be more clear, I'm mainly going to be driving very low impedance coils, (0-5Ohms, ~10uH - 1mH max) at frequencies from DC to about 1Mhz or so. The maximum current I want to be able to source is about 1-5A max. To implement the current regulation scheme, I found this circuit from a Wikipedia page which shows how one can make a simple op-amp voltage to current converter:
http://en.wikipedia.org/wiki/File:I-to-v_op-amp_current_source_1000.jpg
I modified the amplifier schematic in the simulator to use the a 0.1 Ohm sense resistor for a current shunt in the feedback circuit. This allowed me to get an output of 1mA for an input of 1mV into the circuit. This *seemed* to work fine until I attempted to drive a given coil (100uH for example) at higher and higher frequencies. What I found is that the output current started to look more like a triangle wave than a sine wave, I saw that this happens because the feedback voltage was turning into a square wave in attempts to regulate the current, but due to the impedance of the coil, the current couldn't respond fast enough.
So I scrapped that idea and went back to the original schematic, which did produce a nice sinusoidal output, though the current varied with frequency. My next idea was to somehow come up with a feedback circuit that could increase or decrease adjust the output voltage across the coil to keep the current at a set amplitude but without the same issues that I was having with the other scheme. This seems like it shouldn't be that hard to do, but I have no idea how to approach this problem. Is their a better way to do this? Ultimately. what I am trying to make is a current-regulated AC power source.
Thanks,
Jason O
I am faced with a very interesting challenge and I'd like to see if you all could give me any insights. I'm currently planning to design a linear power amplifier loosely based on the design on page 22 of this PDF file here: http://www.wadsworthmedia.com/marketing/sample_chapters/1401848567_ch05.pdf
So far, I have just been doing simulations of the circuit to get a feel for it's operation. However, I want to do a few things different with the design that are, at the moment, throwing me for a loop.
In my application, I am building an amplifier specifically for driving coils of varying inductances at frequencies from 0Hz to about 1MHz (up to 20MHz ideally, but I I'm settling for lower frequency for simplicity). I found that sticking an inductive load works fine with this amplifier design except for the fact that the amperage through the coil varies with frequency due to the coil's inductance.
What I am thinking about is modifying the schematic so that it doesn't utilize voltage regulation but current regulation to keep the coil current constant throughout the frequency range. So, in other words, I want to basically make this into a voltage to current amplifier, with, say 100mV on the input translating to 100mA through the output load.
To be more clear, I'm mainly going to be driving very low impedance coils, (0-5Ohms, ~10uH - 1mH max) at frequencies from DC to about 1Mhz or so. The maximum current I want to be able to source is about 1-5A max. To implement the current regulation scheme, I found this circuit from a Wikipedia page which shows how one can make a simple op-amp voltage to current converter:
http://en.wikipedia.org/wiki/File:I-to-v_op-amp_current_source_1000.jpg
I modified the amplifier schematic in the simulator to use the a 0.1 Ohm sense resistor for a current shunt in the feedback circuit. This allowed me to get an output of 1mA for an input of 1mV into the circuit. This *seemed* to work fine until I attempted to drive a given coil (100uH for example) at higher and higher frequencies. What I found is that the output current started to look more like a triangle wave than a sine wave, I saw that this happens because the feedback voltage was turning into a square wave in attempts to regulate the current, but due to the impedance of the coil, the current couldn't respond fast enough.
So I scrapped that idea and went back to the original schematic, which did produce a nice sinusoidal output, though the current varied with frequency. My next idea was to somehow come up with a feedback circuit that could increase or decrease adjust the output voltage across the coil to keep the current at a set amplitude but without the same issues that I was having with the other scheme. This seems like it shouldn't be that hard to do, but I have no idea how to approach this problem. Is their a better way to do this? Ultimately. what I am trying to make is a current-regulated AC power source.
Thanks,
Jason O