How Does Oscillation Affect Capacitor Voltage After Multiple Cycles?

In summary, a parallel plate capacitor is charged to 20 V and then a simple pendulum with a metal bob is placed in between the plates. After 5 complete oscillations, 10% of the negative charge on the plate is transferred to the bob and neutralized when it touches the positive plate. This means that the potential difference between the plates has decreased by the same fraction. The same applies to the positive charge on the other plate. Therefore, the potential difference between the plates of the capacitor after 5 oscillations is 10% of the original 20 V, or 2 V.
  • #1
thereddevils
438
0

Homework Statement



A parallel plate capacitor is charged by a battery to 20 V and then disconnected . A simple pendulum consists of a metal bob which is suspended by a nylom thread is placed in the middle of the plates of the capacitor . Then the bob is oscillated towards the negative plate of the capacitor . Each time when the bob touches the negative plate , 10 % of the charge at the negative plate will be transferred to the bob and these charges are then neutralised when the bob touches the positive plate of the capacitor . Determine the potential difference between the plates of the capacitor after 5 complete oscillation of the bob .

Homework Equations





The Attempt at a Solution



so i found that 0.1111 of the negative charges have been neutralised and 0.8889 of the -ve charges is left and i am not sure what to do next .
 
Physics news on Phys.org
  • #2
The pd on the capacitor depends on the charge. If it has lost a certain fraction of its charge it should have "lost" the same fraction of its pd.
 
  • #3
Stonebridge said:
The pd on the capacitor depends on the charge. If it has lost a certain fraction of its charge it should have "lost" the same fraction of its pd.

thanks , am i correct in finding the percentage of -ve charge lost from the plate ? When it says the +ve charge from the other plate neutralise the -ve charge , is the +ve charges also decreasing at the same rate as the -ve charges ?
 
  • #4
Yes. If you imagine a charged capacitor that has +10 coulomb on one plate (A) and -10 on the other (B), we say that the capacitor has been charged to 10 coulomb. (Not 20)
If you transfer 1 coulomb of negative charge from plate B to plate A, then plate B has lost 1 coulomb and now has -9, while plate A is now +9. (The one negative charge having neutralised one of the positives.)
The result is that the capacitor now has a charge of 9 coulombs. +9 on the one plate and -9 on the other.
 

Related to How Does Oscillation Affect Capacitor Voltage After Multiple Cycles?

1. What is Pd across the capacitors?

Pd (potential difference) across the capacitors refers to the voltage difference between the two plates of a capacitor. It is measured in volts (V) and is a result of the build-up of electric charge on the plates.

2. How is Pd across the capacitors calculated?

Pd across the capacitors can be calculated by dividing the total charge on the plates by the capacitance of the capacitor. It can also be calculated by multiplying the current flowing through the capacitor by the impedance of the capacitor.

3. What is the significance of Pd across the capacitors?

The Pd across the capacitors is important because it determines the amount of energy stored in the capacitor. It also affects the overall performance and behavior of a circuit.

4. How does Pd across the capacitors affect the charging and discharging of a capacitor?

When the Pd across the capacitors is high, the capacitor will charge faster and reach its maximum voltage more quickly. On the other hand, a lower Pd will result in a slower charging process. During discharging, a higher Pd will cause the capacitor to discharge more quickly.

5. How can Pd across the capacitors be controlled or adjusted?

Pd across the capacitors can be controlled by changing the voltage source connected to the circuit, using resistors in the circuit, or by changing the capacitance of the capacitor itself. It can also be adjusted by using a variable power supply or adjusting the frequency of the AC input.

Similar threads

  • Introductory Physics Homework Help
Replies
18
Views
2K
  • Introductory Physics Homework Help
Replies
3
Views
2K
  • Introductory Physics Homework Help
Replies
3
Views
1K
  • Introductory Physics Homework Help
Replies
26
Views
2K
  • Introductory Physics Homework Help
Replies
17
Views
2K
  • Introductory Physics Homework Help
Replies
3
Views
2K
Replies
9
Views
2K
  • Introductory Physics Homework Help
Replies
2
Views
2K
  • Introductory Physics Homework Help
Replies
9
Views
2K
  • Introductory Physics Homework Help
Replies
8
Views
2K
Back
Top